Insulation in Santa Ana, CA
Spray foam insulation in Santa Ana is the most effective single retrofit for the city’s pre-1950s stucco homes, which were mostly built with empty wall cavities and thin or nonexistent attic insulation. During Santa Ana wind events, when temperatures climb 30–40°F in hours and humidity drops below 10%, those uninsulated cavities turn houses into ovens. Coastal Insulation Santa Ana has served Santa Ana since 2012, and the owner personally installs or directly oversees every job. Call (714) 793-0570 when you’re ready to stop paying for conditioned air that leaks straight through your walls and attic.
Why Santa Ana Homes Are Different
Santa Ana sits in the inland Santa Ana Valley corridor, so it misses the marine-layer temperature buffer that keeps Newport Beach and Huntington Park cooler. Summer attic temperatures here routinely top 150°F, especially during October wind events. That heat doesn’t stay in the attic. It radiates down through the ceiling and pulls conditioned air out of the house all day.
The housing stock compounds the problem. Santa Ana has one of the highest concentrations of pre-1950s small stucco-clad homes in Orange County. Many were built without any wall-cavity insulation at all, just stucco over wood lath or framing. Retrofitting those walls means injection foam or dense-pack blown-in through the exterior or interior, not batt installation, because opening the stucco shell costs more than the insulation itself. The city’s high renter-occupied ratio also means a large share of older rental stock has attic insulation that’s been compressed by decades of HVAC tech foot traffic, pushed aside for rewiring, or matted down by slow roof leaks. The actual R-value is often far below what the landlord thinks. A Santa Ana wind event exposes that gap in a day.
Our Main Santa Ana Services
These are the two jobs Santa Ana homeowners call us about most, and each has its own dedicated page with full pricing and local detail.
Attic Insulation in Santa Ana
Most Santa Ana attics we open up are running at R-11 or less, when California Title 24 expects R-38 or higher. That’s the difference between a house that holds temperature and one that spikes with every wind event. We check the existing material, measure the depth, and recommend whether a top-up or full removal and replacement makes sense for your specific roof and framing. Attic Insulation in Santa Ana covers the full scope, including what fits in tight-pitched older roofs.
Crawl Space Encapsulation & Vapor Barrier in Santa Ana
Santa Ana’s inland humidity swings, from desert-dry during wind events to damp marine air in early summer, create condensation cycles in vented crawl spaces that lead to mold and musty odors. Sealing the crawl space with a vapor barrier and dehumidification stops that cycle at the source. Crawl Space Encapsulation & Vapor Barrier in Santa Ana explains the process, pricing, and why it matters for your floors and indoor air.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Santa Ana
Spray foam insulation in Santa Ana solves the single biggest problem in pre-1950s stucco homes: walls and roof decks with zero cavity sealing. Open-cell foam works for most attic and ceiling applications, while closed-cell foam adds structural shear strength and moisture resistance for older framing. During a Santa Ana wind event, when outside air hits 100°F with 8% humidity, a properly sealed foam envelope is the difference between an HVAC system that cycles and one that runs constantly. Our owner personally installs or directly oversees every Spray Foam Insulation job, and we carry both Icynene and Demilec to match the right density to each surface.
Open-Cell Spray Foam
Signs you need it
Rooms at the top of the house stay hot long after the sun sets, or you hear every leaf blower on the block through the attic.
What it costs in Santa Ana
Open-cell spray foam in Santa Ana runs $2.00 to $3.50 per square foot, with most attic applications landing between $1,800 and $5,500 depending on depth and access.
How we do it
We prep the attic by moving any compressed existing insulation, mask off the hatch, and spray the roof deck or ceiling plane to the specified R-value, usually R-38 for Santa Ana attics.
Closed-Cell Spray Foam
Signs you need it
You have uninsulated stucco walls from the 1940s or 1950s, or you want the highest R-value per inch in a tight roofline.
What it costs in Santa Ana
Closed-cell spray foam in Santa Ana runs $3.50 to $5.50 per square foot, and most full-wall retrofits range from $4,000 to $9,000 with drilling and patching included.
How we do it
We drill access holes in the stucco or interior plaster, inject the foam to fill each stud cavity, and patch the holes to match the original surface. The owner stays on site through the entire spray.
Garage Ceiling Spray Foam
Signs you need it
The garage hits 110°F by noon in summer, or a bedroom above the garage stays noticeably hotter than the rest of the house.
What it costs in Santa Ana
Garage ceiling spray foam in Santa Ana typically runs $1,500 to $3,200 for a two-car garage, depending on whether the roof deck or ceiling joists get sprayed.
How we do it
We seal the ceiling plane and any gaps around the garage door header, then spray open-cell foam to R-30 or R-38 with a clean thermal boundary.
What Spray Foam Insulation Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Open-cell spray foam (attic, R-38) | $1,800 – $5,500 |
| Closed-cell spray foam (wall retrofit) | $4,000 – $9,000 |
| Garage ceiling spray foam | $1,500 – $3,200 |
| Rim joist spray foam | $800 – $1,800 |
Is closed-cell foam worth the extra cost in Santa Ana?
For uninsulated stucco walls, yes. Closed-cell foam adds structural shear strength and moisture resistance that open-cell can’t match, and it delivers R-7 per inch in a cavity where space is fixed. Call (714) 793-0570 for a wall-by-wall assessment.
Can you spray foam a Santa Ana attic during October wind season?
Yes, but scheduling fills fast. Wind events make under-insulated homes unbearable, so homeowners book foam retrofits in September and October. Call early for the best window, estimates are free.
Blown-In Insulation in Santa Ana
Blown-in insulation in Santa Ana is the fastest way to bring a compressed or thin attic up to Title 24 code without tearing out the existing material. Most older Santa Ana homes have fiberglass batts that measured R-19 when installed but now test at R-8 after decades of foot traffic and roof leaks. A dense top-up with blown-in fiberglass or cellulose restores the full thermal barrier in an afternoon. We carry both Johns Manville fiberglass and GreenFiber cellulose for Blown-In Insulation, and the owner runs the machine on every job so the material is applied at the correct density, not fluffed and overblown.
Blown-In Cellulose
Signs you need it
You want a higher recycled-content material, or your existing attic insulation is thin, matted, and no longer springy.
What it costs in Santa Ana
Blown-in cellulose in Santa Ana runs $1.50 to $2.75 per square foot, with most 1,000-square-foot attics landing between $1,500 and $2,800 for R-38.
How we do it
We air-seal the attic floor first, then blow cellulose to the target depth using a calibrated machine, checking density with a ruler at multiple points.
Blown-In Fiberglass
Signs you need it
You want a lower-dust material, or you’re topping up existing fiberglass batts and want a consistent product match.
What it costs in Santa Ana
Blown-in fiberglass in Santa Ana runs $1.75 to $3.00 per square foot, with a typical 1,000-square-foot attic at R-38 landing between $1,800 and $3,100.
How we do it
We lay a fresh, even layer over the existing material after air-sealing the floor, taking care not to block soffit vents or bury can lights without proper covers.
What Blown-In Insulation Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Blown-in cellulose (attic, R-38) | $1,500 – $2,800 |
| Blown-in fiberglass (attic, R-38) | $1,800 – $3,100 |
| Dense-pack wall retro-fit | $3,500 – $8,000 |
| Blown-in top-up (over existing) | $900 – $2,200 |
Does blown-in insulation settle in Santa Ana’s dry heat?
Cellulose settles slightly after installation, which is why we install it at a density that accounts for that. Fiberglass settles less. Either material, installed to spec, holds its R-value for decades. Call for an exact attic evaluation.
Can you blow insulation into walls that have old stucco?
Yes, dense-pack blown-in works through small drill holes in the stucco or interior drywall, filling each cavity without opening the wall. It’s the standard retrofit for pre-1950s Santa Ana homes.
Radiant Barrier Installation in Santa Ana
Radiant barrier installation in Santa Ana targets what standard insulation can’t reach: radiant heat from the sun’s energy hitting your roof deck. When attic temperatures hit 150°F during a wind event, a radiant barrier reflects a large share of that heat before it radiates into the attic space. The result is a cooler attic, which means a cooler ceiling, which means your HVAC doesn’t fight the sun all afternoon. We install Radiant Barrier Installation as part of a full attic strategy, never as a replacement for insulation but as a layer that makes the insulation you have work better.
Attic Radiant Barrier
Signs you need it
Your attic is 30°F hotter than outside on summer afternoons, or your upstairs rooms won’t cool below 80°F even with the AC running.
What it costs in Santa Ana
An attic radiant barrier in Santa Ana runs $1.25 to $2.50 per square foot, with most homes landing between $1,500 and $3,800 depending on roof geometry.
How we do it
We staple the foil barrier to the underside of the rafters or lay it over the attic floor, creating a continuous reflective plane with air gaps maintained for proper function.
Radiant Barrier Roof Deck
Signs you need it
You’re re-roofing anyway, or you want the cleanest install with no attic-floor disruption.
What it costs in Santa Ana
Roof deck radiant barrier in Santa Ana runs $1.00 to $2.00 per square foot, with typical homes ranging from $1,200 to $3,200 when installed during re-roofing.
How we do it
We coordinate with the roofer to lay the barrier directly on the deck before shingles go on, which gives full coverage with zero fasteners inside the attic.
What Radiant Barrier Installation Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Attic radiant barrier | $1,500 – $3,800 |
| Roof deck radiant barrier | $1,200 – $3,200 |
| Radiant barrier foil (material only) | $300 – $800 |
| Radiant barrier + ventilation upgrade | $2,000 – $4,500 |
Does a radiant barrier help in winter in Santa Ana?
It helps less in winter because the sun angle is lower and the primary heat direction is upward from the home, not downward from the roof. Its biggest value here is the summer wind-event season. Call to see if your attic geometry is a good fit.
Will a radiant barrier replace the need for insulation?
No. It reduces radiant heat gain but does not slow conductive heat transfer. You still need proper R-value insulation. The two work together. We can assess both in one visit.
Insulation Removal & Replacement in Santa Ana
Insulation removal and replacement in Santa Ana is the right call when existing material has been soaked by roof leaks, chewed through by rats, or compressed over decades in homes where HVAC techs have trampled down the attic. Santa Ana’s older rental stock is especially prone to this: repeated rewiring jobs and slow leaks leave insulation matted and ineffective long before a landlord notices. We remove the old material, sanitize the attic floor, seal the thermal boundary, and re-insulate to current Title 24 R-values. Our Insulation Removal & Replacement crew handles contaminated material safely, with proper containment and disposal for Santa Ana’s older homes.
Attic Insulation Removal
Signs you need it
Your insulation is stained, matted, smells musty, or you’ve found rodent droppings scattered through the material.
What it costs in Santa Ana
Attic insulation removal in Santa Ana runs $1.00 to $1.75 per square foot, with most homes landing between $1,200 and $2,500 for a 1,000-square-foot attic.
How we do it
We vacuum out the old material with a high-powered machine, bag it for disposal, and leave the attic floor clean for inspection and air sealing.
Contaminated Insulation Removal
Signs you need it
You see rodent nests, droppings, or urine stains in the insulation, or you’ve had a wildlife exclusion done and the attic still smells.
What it costs in Santa Ana
Contaminated insulation removal in Santa Ana runs $1.50 to $2.50 per square foot, with full sanitization and replacement typically ranging from $3,000 to $7,000 total.
How we do it
We use containment and negative air where needed, remove all contaminated material, sanitize the attic surfaces, and install fresh insulation with proper protective gear.
What Insulation Removal & Replacement Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Attic insulation removal | $1,200 – $2,500 |
| Contaminated insulation removal + sanitize | $2,000 – $4,500 |
| Full removal + replacement (attic) | $3,000 – $7,000 |
| Vermiculite & old insulation removal | $2,500 – $6,000 |
How do I know if my Santa Ana attic insulation needs removal?
If it has been wet, compressed to half its original depth, chewed through, or saturated with dust and droppings, it has lost its R-value and should come out. We can inspect and tell you straight. Estimates are free.
Can you remove insulation in an occupied Santa Ana home?
Yes. We contain the work area, run negative air where needed, and schedule removal during hours that minimize disruption. No one needs to leave the home for a standard attic removal.
Attic Air Sealing in Santa Ana
Attic air sealing in Santa Ana stops the stack effect that pulls air from the house up through every gap and crack into the attic. In a city where summer attics hit 150°F, those gaps aren’t just letting conditioned air out. They’re pulling hot, dusty attic air down into the house whenever the AC kicks on and creates negative pressure. Sealing the attic floor is the single highest-value prep step before adding insulation, because insulation doesn’t stop air movement. We seal the ceiling plane, top plates, wiring penetrations, and can lights before a single bag of insulation goes in. Our Attic Air Sealing work follows Title 24 requirements for Santa Ana permitted jobs.
Attic Floor Air Sealing
Signs you need it
Rooms feel dusty even with clean filters, or you feel drafts near ceiling fixtures when the AC runs.
What it costs in Santa Ana
Attic floor air sealing in Santa Ana runs $1.00 to $1.75 per square foot, with most homes landing between $1,000 and $2,800 depending on attic accessibility.
How we do it
We clear the insulation from each area, seal every visible gap and seam with foam or caulk, and re-lay the insulation flat.
Can Light & Duct Boot Sealing
Signs you need it
You have recessed can lights in the ceiling below the attic, or you feel airflow around ceiling registers.
What it costs in Santa Ana
Can light and duct boot sealing in Santa Ana runs $350 to $900 for a typical home with 8 to 15 penetrations.
How we do it
We install approved covers over can lights or seal around them with the correct material, and wrap and seal duct boots at the ceiling plane.
What Attic Air Sealing Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Attic floor air sealing | $1,000 – $2,800 |
| Top plate & penetration sealing | $1,200 – $3,000 |
| Can light & duct boot sealing | $350 – $900 |
| Attic hatch sealing | $250 – $600 |
Does air sealing make a noticeable difference in Santa Ana summers?
Yes. Stopping air movement through the ceiling plane keeps conditioned air inside and hot attic air out. Many homeowners notice the difference immediately in upstairs rooms. Call (714) 793-0570 for an attic inspection.
Is air sealing required before adding insulation in Santa Ana?
California Title 24 requires air sealing on permitted insulation jobs. Even on unpermitted top-ups, it’s the right technical sequence. We never skip it.
Wall Insulation in Santa Ana
Wall insulation in Santa Ana is the retrofit that treats the biggest hidden problem in the city’s housing stock: pre-1950s stucco homes with empty wall cavities. Those 2×4 stud bays were never insulated, so the walls radiate heat inward all afternoon during wind events. Because Santa Ana’s stucco shells are expensive to open, we use injection foam and dense-pack blown-in techniques that fill cavities through small holes. We carry CertainTeed fiberglass and Rockwool mineral wool for Wall Insulation jobs, and the owner handles the drill-and-fill work personally so every cavity gets the right density.
Injection Foam Wall Insulation
Signs you need it
Exterior walls feel warm to the touch in summer, or rooms along the west side of the house heat up far faster than north-facing rooms.
What it costs in Santa Ana
Injection foam wall insulation in Santa Ana runs $3.50 to $5.50 per square foot of wall area, with most single-story homes ranging from $4,000 to $9,000.
How we do it
We drill small access holes in the stucco or interior, inject foam into each cavity at controlled pressure, and patch the holes to match the surface.
Drill & Fill Wall Insulation
Signs you need it
You have uninsulated walls and prefer a dense-pack material like cellulose or fiberglass rather than foam.
What it costs in Santa Ana
Drill and fill wall insulation in Santa Ana runs $2.50 to $4.00 per square foot, with typical homes landing between $3,500 and $8,000, though patching costs vary by stucco finish.
How we do it
We drill into each stud bay, pack the material with a high-pressure blower, and verify density with an infrared camera before patching.
What Wall Insulation Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Injection foam wall insulation | $4,000 – $9,000 |
| Drill & fill wall insulation | $3,500 – $8,000 |
| Exterior wall insulation (new construction) | $2,000 – $5,000 |
| Interior wall soundproofing | $1,500 – $3,500 |
Can you insulate walls in a Santa Ana home without removing the stucco?
Yes. Both injection foam and dense-pack drill-and-fill work through small holes, so the stucco shell stays intact. This is the standard approach for Santa Ana’s older homes. Call for a wall inspection.
How do I know if my Santa Ana walls are already insulated?
An infrared camera tells us in minutes. We can also remove an outlet cover on an exterior wall and look inside the cavity. Most pre-1950s Santa Ana homes have empty bays.
Attic Cleaning & Rodent Proofing in Santa Ana
Attic cleaning and rodent proofing in Santa Ana addresses a problem that’s worse here than in most Orange County cities: older rental stock and pre-1950s homes have dozens of entry points that rats and squirrels exploit, and the damage they do to insulation is permanent. Santa Ana’s mature tree canopy and dense neighborhoods mean roof rats are active year-round, not seasonally. Once they’re in, they chew wires, tear insulation, and leave droppings that contaminate the material. We remo ve the damaged insulation, sanitize the attic, seal every entry point, and re-insulate. Our Attic Cleaning & Rodent Proofing work treats the full problem, not just the mess.
Attic Cleanout
Signs you need it
You hear scratching in the ceiling at night, find droppings in the attic, or see damaged insulation with tunnels running through it.
What it costs in Santa Ana
An attic cleanout in Santa Ana runs $800 to $2,000 for a typical 1,000-square-foot attic, with contaminated material removal adding $1,500 to $3,500.
How we do it
We remove all contaminated or damaged insulation, vacuum the attic floor, and prepare the space for sanitizing and new insulation.
Rodent Proofing & Exclusion
Signs you need it
Rodents return after previous removal attempts, or you see chewed openings around vents, eaves, and roof junctions.
What it costs in Santa Ana
Rodent proofing and exclusion in Santa Ana runs $1,200 to $3,500, depending on the number of entry points and the roof’s accessibility.
How we do it
We inspect the full roof perimeter and attic, seal entry points with steel mesh and foam, and verify the attic stays clean after the work.
What Attic Cleaning & Rodent Proofing Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Attic cleanout | $800 – $2,000 |
| Attic sanitizing & decontamination | $1,500 – $3,500 |
| Rodent proofing & exclusion | $1,200 – $3,500 |
| Full attic restoration (clean + proof + re-insulate) | $4,000 – $9,000 |
Does rodent proofing keep rats out of a Santa Ana home permanently?
If we seal every entry point, yes. Rats can’t chew through properly installed steel mesh and foam. The key is finding all the openings, not just the obvious ones. Call for a full roof-perimeter inspection.
Can you clean the attic and re-insulate in one visit?
Usually yes. We schedule the cleanout, sanitizing, proofing, and re-insulation as one continuous job so the attic is left clean, sealed, and properly insulated.
Home Energy Audit in Santa Ana
A home energy audit in Santa Ana tells you exactly where your conditioned air is going before you spend money on insulation or sealing. Most pre-1950s stucco homes here leak air through the ceiling plane, uninsulated wall cavities, and ductwork at a rate that surprises even experienced homeowners. An audit measures the actual air leakage with a blower door test and finds the thermal weak spots with an infrared camera. We use the results to write a prioritized, price-specific plan for your Santa Ana home. Our Home Energy Audit is the diagnostic first step before any insulation work, not an afterthought.
Blower Door Test
Signs you need it
You can’t figure out why energy bills stay high despite a newer AC unit, or rooms feel drafty in winter and stuffy in summer.
What it costs in Santa Ana
A blower door test in Santa Ana runs $250 to $500 as part of a full audit, or $300 to $700 as a standalone test.
How we do it
We mount the blower door in an exterior door frame, depressurize the house, and measure the cubic feet per minute of air leakage with calibrated gauges.
Thermal Imaging Inspection
Signs you need it
You suspect missing insulation in walls or ceilings but don’t want to open anything up to find out.
What it costs in Santa Ana
A thermal imaging inspection in Santa Ana runs $200 to $450 as part of an audit, and $300 to $600 when done as a standalone scan.
How we do it
We scan walls, ceilings, and the attic floor with an infrared camera while the home is depressurized, so air leaks show as thermal anomalies on the screen.
What Home Energy Audit Costs in Santa Ana
| Item | Typical range in Santa Ana |
|---|---|
| Full home energy audit | $450 – $900 |
| Blower door test (standalone) | $300 – $700 |
| Thermal imaging inspection | $300 – $600 |
| Duct leakage test | $250 – $550 |
Is a home energy audit worth it in Santa Ana before insulating?
Yes. It tells us which leaks to seal first, which walls have empty cavities, and whether your ducts are losing air. Without it, you’re guessing. Call (714) 793-0570 to schedule one.
Does a Santa Ana energy audit meet Title 24 requirements?
A blower door test is a required component for many permitted insulation jobs under Title 24. Our tests follow the standard protocols, and the results are documented for your permit file.
Brands We Service in Santa Ana
We work with Johns Manville, Knauf, Rockwool, and CertainTeed because each fills a specific need in Santa Ana’s housing stock, from Rockwool’s fire resistance on older framing to CertainTeed’s fiberglass for clean top-ups. Most materials are stocked locally, so typical jobs start within days. See our brands for the full range.
Pricing for Insulation in Santa Ana, CA
| Service | Typical range in Santa Ana |
|---|---|
| Open-cell spray foam (attic) | $1,800 – $5,500 |
| Closed-cell spray foam (wall retrofit) | $4,000 – $9,000 |
| Blown-in cellulose (attic, R-38) | $1,500 – $2,800 |
| Blown-in fiberglass (attic, R-38) | $1,800 – $3,100 |
| Attic radiant barrier | $1,500 – $3,800 |
| Attic insulation removal | $1,200 – $2,500 |
| Attic floor air sealing | $1,000 – $2,800 |
| Injection foam wall insulation | $4,000 – $9,000 |
| Attic cleanout + rodent proofing | $2,000 – $5,500 |
| Full home energy audit | $450 – $900 |
Prices in Santa Ana rise with stucco patching costs on wall retrofits, steep roof pitches that make attics harder to work in, and rodent contamination that requires sanitizing before re-insulation. We give upfront pricing on every job, so the number you get at the estimate is the number on the invoice.
Neighborhoods We Serve in Santa Ana
We work in every corner of Santa Ana, from the older stucco homes near downtown to the mid-century tracts that spread out from Main Street. Most neighborhoods have a mix of pre-1950s and 1960s-era construction, which changes the right insulation approach from block to block. Response time for most areas is same-week for estimates and one to two weeks for scheduled work.
- Floral Park
- French Park
- West Floral Park
- Washington Square
- Wilshire Square
Service Area — Cities Near Santa Ana
We also serve Tustin, CA, Villa Park, CA, Fountain Valley, CA, and Newport Beach, CA. Each city has its own insulation realities, from Tustin’s older tract homes to Newport Beach’s coastal humidity, and we adjust materials and techniques accordingly.
Serving Santa Ana, CA — Our Local Coverage Area
We’re based in the Santa Ana area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Insulation in Santa Ana
We can usually get a same-week estimate on the calendar, and most emergency work starts within one to two weeks. During October wind events, scheduling fills quickly, so call (714) 793-0570 as soon as you know you need work.
Permitted insulation work in Santa Ana must meet California Title 24 energy code requirements, including air sealing and blower door verification. We handle the permit coordination and tests as part of the job.
Yes. Most of the pre-1950s Santa Ana housing stock has plaster over wood lath, and we have the right techniques for injection foam and drill-and-fill wall retrofits that work with plaster without cracking it. The key is controlled pressure and the right patching approach.
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Santa Ana Customers Say
"Work is good and the house is noticeably more comfortable. There was insulation debris left in the hall closet under the attic access that I had to clean up."
— Kristen Miller"Solid job. It's hard to verify what's up there once they've gone, so I'd suggest asking for photos, which they did provide when I asked but didn't offer."
— Neil Bennett"Found and sealed a gap around the chimney chase that was basically an open chimney to the attic."
— Rafael Vargas