Insulation in Placentia, CA
Spray foam insulation in Placentia solves a problem most of this city’s 1960s-to-1980s tract homes were never built to handle: empty wall cavities and undersized attic batts that can’t keep up with CEC Climate Zone 10. Summer highs regularly push into the mid-90s°F, winter nights drop enough to matter, and Santa Ana wind events can swing outdoor temperatures 20–30°F within hours. Coastal Insulation Santa Ana has served Placentia since 2012, and the owner performs or directly oversees every install. Call (714) 793-0570 for a free estimate on any insulation job below.
Why Placentia Homes Are Different
Placentia’s housing stock tells a specific story. The master-planned subdivisions built between 1963 and 1985 went up when California energy codes demanded little to no wall insulation, so a large share of these stucco-clad homes still have empty stud cavities. Attic insulation in the same homes is usually settled R-11 fiberglass, far below what Title 24 requires today. Because Placentia sits inland enough to miss the coastal marine layer that moderates Anaheim or Fullerton, the penalty for uninsulated walls is bigger here. Homes backing up to the Puente Hills open space face a second issue: rats and ground squirrels migrate from the adjacent preserves and shred attic insulation, so many Placentia attics need full removal and re-insulation rather than a simple top-off. Older sections near Old Town Placentia add a handful of pre-1950 Craftsman bungalows with even less thermal protection than the tract homes around them.
Our Main Placentia Services
Two services generate the most calls from Placentia homeowners: attic insulation, because so many homes still sit on original or settled batts, and crawl space encapsulation, because inland temperature swings create the kind of humidity and moisture conditions that make vented crawl spaces a problem.
Attic Insulation in Placentia
Most Placentia attics were built for a climate that no longer matches reality. The R-11 or R-19 batts installed in the 1970s and 1980s have settled, compressed, and stopped resisting heat the way they should, which is why upstairs rooms in these homes routinely run 10–15 degrees warmer than downstairs in July. We inspect the existing attic floor, air-seal the penetrations, and then build the insulation layer back to current Title 24 levels using blown-in or batt material matched to your home’s specific conditions. See the full breakdown on our Attic Insulation in Placentia page.
Crawl Space Encapsulation & Vapor Barrier in Placentia
Placentia’s inland heat and cool winter nights create the exact conditions that make vented crawl spaces trap moisture: warm, humid air enters the crawl, hits cooler surfaces, and condenses. That shows up as musty smells, warped floors, and mold on the joists. We seal the crawl space from the ground up with a reinforced vapor barrier, seal vents and rim joist leaks, and condition the space so it stops pulling damp air into the house. Details are on our Crawl Space Encapsulation & Vapor Barrier in Placentia page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Placentia
Spray foam insulation in Placentia addresses the single biggest shortfall in this city’s tract housing: walls with no cavity insulation and attics with settled R-11 batts that can’t handle Climate Zone 10 summer loads. Because Placentia misses the coastal marine layer, the cooling penalty of a poorly insulated attic hits harder here than in coastal Orange County cities just 15 miles west, and closed-cell Spray Foam Insulation fills and seals in one pass. It’s the fastest way to correct the heat gain that makes upstairs rooms in 1960s and 1970s tract homes feel like ovens by mid-afternoon.
Open-Cell Spray Foam
Signs you need it
Upstairs rooms stay hot long after the AC shuts off, or you hear every footstep and conversation from the rooms above. Open-cell foam’s air-sealing property means the attic stops acting as a heat exchange chamber.
What it costs in Placentia
Open-cell spray foam in Placentia typically runs $2.10 to $4.00 per board foot, depending on depth and access.
How we do it
We prep the attic or wall cavity, then apply open-cell foam directly to the underside of the roof deck or into stud bays where it expands to fill gaps and block airflow before we trim it flush.
Closed-Cell Spray Foam
Signs you need it
You want structural strength plus insulation in a single material, or you need the highest R-value per inch in a tight space like a rim joist or a shallow roof cavity.
What it costs in Placentia
Closed-cell spray foam in Placentia typically ranges from $3.20 to $6.50 per board foot because of the material density and the two-pound chemistry involved.
How we do it
We apply the closed-cell foam in controlled passes so it builds to the specified thickness, then inspect the finished surface to confirm full coverage with no voids or soft spots.
Rim Joist Spray Foam
Signs you need it
You feel cold air near the baseboards in winter, or your utility bills spike in Santa Ana wind events. The rim joist is the most common air leak in Placentia’s slab-on-grade tract homes.
What it costs in Placentia
Rim joist spray foam in Placentia is usually priced by the linear foot and typically falls between $8 and $16 per linear foot for closed-cell application.
How we do it
We access the rim joist from the crawl space or basement, clean the surface, and apply closed-cell foam to seal the band joist against both air movement and moisture intrusion.
What Spray Foam Insulation Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Open-cell spray foam | $2.10 – $4.00 per board foot |
| Closed-cell spray foam | $3.20 – $6.50 per board foot |
| Rim joist spray foam | $8 – $16 per linear foot |
| Attic roof deck spray foam | $3.20 – $6.50 per board foot |
Is spray foam worth it in Placentia’s climate?
Yes. Placentia’s inland position means cooling dominates the energy bill and hot, dry Santa Ana winds push heat into attics fast. Spray foam’s air-sealing and R-value per inch combination corrects that faster than any batt or blow-in retrofit, which shortens the payback window on tract homes with empty walls.
Can you spray foam my Placentia home without removing the old insulation?
In most attics, old batts or blown-in material must come out before foam goes in, because foam won’t bond properly to dusty, settled insulation. We’ll tell you during the inspection if removal is required and fold that into the quote so the number you get is the number you pay.
Blown-In Insulation in Placentia
Blown-in insulation in Placentia is the practical retrofit for the thousands of tract homes built between 1963 and 1985 with settled R-11 attic batts and no wall cavity insulation. Because Placentia sits in Climate Zone 10 and regularly hits mid-90s°F summer highs, that thin attic layer costs real money every cooling season. Blown-In Insulation fills gaps that batts can never reach, and it’s the fastest way to bring an attic floor back to current code without rebuilding anything.
Blown-In Cellulose
Signs you need it
Your attic insulation looks thin and uneven, or you prefer a recycled-content material. Cellulose settles less than loose fiberglass and blocks airflow better because of its density.
What it costs in Placentia
Blown-in cellulose in Placentia typically runs $1.50 to $3.00 per square foot installed, including prep and cleanup.
How we do it
We remove any contaminated material, air-seal the attic floor, then blow cellulose to the depth specified for your R-value target using calibrated equipment so the coverage is even.
Dense-Pack Wall Insulation
Signs you need it
Your Placentia tract home has empty stucco wall cavities and rooms that never hold temperature. Dense-pack fills those closed bays through small access holes without tearing out drywall.
What it costs in Placentia
Dense-pack wall insulation in Placentia typically ranges from $3.50 to $7.00 per square foot of wall area because of the drilling, packing, and patching involved.
How we do it
We drill access holes through the exterior or interior wall surface, pack cellulose or fiberglass into the cavity to the correct density, then patch each access point cleanly.
Blown-In Top-Up
Signs you need it
Your existing attic insulation is dry, clean, and pest-free, but just too thin for current code. A top-up adds R-value without the cost of full removal.
What it costs in Placentia
A blown-in top-up in Placentia typically falls between $1.00 and $2.50 per square foot, depending on the depth you need added.
How we do it
We verify the existing material is dry and uncontaminated, then blow new insulation directly over it to reach your target R-value, checking depth with markers as we go.
What Blown-In Insulation Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Blown-in cellulose | $1.50 – $3.00 per sq ft |
| Blown-in fiberglass | $1.50 – $3.00 per sq ft |
| Dense-pack wall insulation | $3.50 – $7.00 per sq ft |
| Blown-in top-up | $1.00 – $2.50 per sq ft |
Is blown-in insulation enough for Placentia summers?
Yes, when installed to the correct R-value and paired with attic air sealing. Blown-in material fills the entire attic floor without gaps, which is exactly what Placentia’s settled batts no longer do. For empty wall cavities, dense-pack blown-in is the standard retrofit method.
How long does a blown-in insulation job take in Placentia?
Most attic blow-in jobs finish in a single day. Wall dense-pack runs longer because of the drilling and patching, but our crew’s time on site is defined by square footage, not schedule padding. Call (714) 793-0570 for a specific timeline on your home.
Radiant Barrier Installation in Placentia
Radiant barrier installation in Placentia attacks the problem most specific to this city’s climate: heat that pours through the roof deck into the attic during long inland summer afternoons. Placentia’s highs in the mid-90s°F and its Santa Ana wind corridor turn attics into ovens, and even good insulation can’t stop radiant heat gain effectively. A Radiant Barrier Installation reflects that heat back before it ever reaches the insulation or the living space below.
Attic Radiant Barrier
Signs you need it
Your attic is unbearably hot by noon even with insulation in place, or your AC runs constantly on days when the outdoor temperature barely passes 90°F.
What it costs in Placentia
Attic radiant barrier in Placentia typically ranges from $1.50 to $3.50 per square foot of attic floor area, depending on the installation method.
How we do it
We staple the radiant barrier to the underside of the roof rafters, leaving the proper air gap at the ridge so heat reflects back outward and doesn’t transfer to the insulation below.
Radiant Barrier Roof Deck
Signs you need it
You’re re-roofing, building an addition, or want the most effective radiant heat protection available because roof-deck application stops heat before it enters the attic at all.
What it costs in Placentia
Roof-deck radiant barrier in Placentia is usually installed as part of a roofing project and adds roughly $0.50 to $1.50 per square foot to the decking cost.
How we do it
We coordinate with your roofer to lay the foil-faced decking or apply the barrier product directly to the substrate before shingles or tile go on, so the reflective surface faces downward into the attic.
What Radiant Barrier Installation Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Attic radiant barrier | $1.50 – $3.50 per sq ft |
| Radiant barrier foil | $1.50 – $3.50 per sq ft |
| Radiant barrier roof deck | $0.50 – $1.50 per sq ft (add-on) |
| Radiant barrier with ventilation | $1.50 – $3.50 per sq ft |
Does a radiant barrier help in Placentia winter too?
A modest amount. Radiant barriers primarily reduce summer heat gain, which is Placentia’s dominant cooling problem. In winter they reflect some heat back into the home from the attic, but the real savings come from cutting air conditioning loads in the hottest months.
Can a radiant barrier be added to any Placentia home?
Most attic configurations can accept a radiant barrier, though very low-slope roofs or attics with restricted access need a site inspection first. We’ll check your roof pitch and attic space before you commit, so call (714) 793-0570 to schedule a look.
Insulation Removal & Replacement in Placentia
Insulation removal and replacement in Placentia is often the only correct fix for two local problems: rodent damage from the Puente Hills open space and decades of settled, compressed batts in 1960s–1980s tract homes. Simply topping off contaminated or collapsed insulation traps the problem under a clean layer. Insulation Removal & Replacement starts with getting everything out, inspecting the attic, and rebuilding the insulation layer from a clean deck.
Attic Insulation Removal
Signs you need it
Your attic insulation is visibly settled, matted, or compressed from decades of heat and foot traffic, and it’s no longer filling the joist bays the way it should.
What it costs in Placentia
Attic insulation removal in Placentia typically ranges from $1.00 to $2.50 per square foot, depending on depth and access.
How we do it
We use a commercial vacuum system to pull out the old material to the deck, bag it for disposal, and leave the attic floor clean enough to inspect for air leaks and damage.
Contaminated Insulation Removal
Signs you need it
You see droppings, tunnels, or nesting debris in the insulation, or you smell a persistent musty odor from the attic. Homes near the Puente Hills preserves deal with this more than most.
What it costs in Placentia
Contaminated insulation removal in Placentia typically runs $2.00 to $4.50 per square foot because of the containment and disposal protocols required.
How we do it
We seal the work area, remove contaminated material in heavy-duty bags, and sanitize the attic surfaces before any new insulation goes down, so the space is clean and safe.
Vermiculite & Old Insulation Removal
Signs you need it
Your pre-1950 Old Town Placentia bungalow may still have origina vermiculite or an unrecognizable loose material that predates modern fiberglass or cellulose.
What it costs in Placentia
Vermiculite and old insulation removal in Placentia typically falls between $3.00 and $6.00 per square foot due to the extra handling requirements.
How we do it
We treat any vermiculite as potentially asbestos-containing, follow safe-removal procedures, and replace it with a modern material that meets current code for your home type.
What Insulation Removal & Replacement Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Attic insulation removal | $1.00 – $2.50 per sq ft |
| Contaminated insulation removal | $2.00 – $4.50 per sq ft |
| Vermiculite & old insulation removal | $3.00 – $6.00 per sq ft |
| Insulation replacement | $1.50 – $3.50 per sq ft |
Can you remove and replace insulation in one day in Placentia?
For a standard attic, yes. Removal, air sealing where needed, and new blown-in installation typically finish same-day on homes under 2,000 square feet of attic floor. Larger or heavily contaminated attics may run into a second day.
Is it cheaper to just top off my Placentia attic than remove and replace?
Sometimes, but not when the existing material is rodent-damaged, damp, or concentrated with dust and droppings. In those cases removal is cheaper long-term because topping off locks in the air quality and R-value problems you already have.
Attic Air Sealing in Placentia
Attic air sealing in Placentia corrects the invisible problem that makes even a well-insulated home feel drafty and expensive to cool: the dozens of small penetrations between your living space and the attic. During Santa Ana wind events, Placentia’s hot, dry offshore gusts push outdoor air through those gaps fast, and a leaky attic floor lets conditioned air escape year-round. Attic Air Sealing closes those bypasses so your insulation can actually do its job.
Attic Floor Air Sealing
Signs you need it
You feel drafts inside the house even with windows closed, or dust builds up quickly on surfaces. Both are classic signs of air moving through the attic floor into the rooms below.
What it costs in Placentia
Attic floor air sealing in Placentia typically ranges from $1.50 to $3.50 per square foot, depending on how many penetrations need sealing.
How we do it
We pull back or remove the existing insulation, seal every penetration with foam or mastic, and then reinstall or replace the insulation over a genuinely sealed floor.
Top Plate & Penetration Sealing
Signs you need it
Rooms feel warm and stuffy in summer regardless of thermostat setting. The top plate the gap where your walls meet the attic is the single biggest leak in most Placentia tract homes.
What it costs in Placentia
Top plate and penetration sealing in Placentia usually falls between $1.50 and $3.50 per square foot, since the work is labor-intensive and detail-driven.
How we do it
We work along every linear foot of the top plates, sealing them with foam or caulk, then treat plumbing stacks, electrical penetrations, and any other bypass with the appropriate material.
Can Light & Duct Boot Sealing
Signs you need it
Your ceiling has recessed can lights that feel warm to the touch, or your HVAC duct connections in the attic are leaking air you paid to condition.
What it costs in Placentia
Can light and duct boot sealing in Placentia is typically priced per fixture or opening, usually $15 to $35 per unit.
How we do it
We seal each can light housing with a rated cover or sealant, then mastic every duct boot, register, and joint in the attic so the air path stays inside the ducts.
What Attic Air Sealing Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Attic floor air sealing | $1.50 – $3.50 per sq ft |
| Top plate & penetration sealing | $1.50 – $3.50 per sq ft |
| Can light sealing | $15 – $35 per unit |
| Duct boot sealing | $15 – $35 per unit |
Does air sealing matter more than insulation in Placentia?
They work together, but sealing often delivers the faster comfort gain. A well-sealed attic with thin insulation outperforms a heavily insulated but leaky attic because air movement is what carries most of the heat transfer in Placentia’s wind-corridor conditions.
How do I know if my Placentia attic needs air sealing?
Look for uneven room temperatures, dust, or unusually high cooling bills. The definitive answer comes from a blower door test during a home energy audit, which gives you a measured number for your home’s leakage. Call (714) 793-0570 to set one up.
Wall Insulation in Placentia
Wall insulation in Placentia addresses the most overlooked defect in this city’s tract housing: stucco-clad walls built with no insulation at all in the stud cavities. Those empty bays are why rooms on the west side of a Placentia home turn punishingly hot by late afternoon and why heating costs stay stubbornly high through winter nights. Wall Insulation fills those cavities through small access holes, turning a thermal sieve into a proper envelope without gutting the drywall.
Injection Foam Wall Insulation
Signs you need it
Your walls feel cold to the touch in winter, or the rooms never hold a set temperature. Injection foam is the cleanest retrofit for empty Placentia stud bays.
What it costs in Placentia
Injection foam wall insulation in Placentia typically ranges from $4.00 to $8.00 per square foot of wall area, including patching.
How we do it
We drill small access holes, inject the foam into each stud cavity where it expands and fills the void, then patch the holes so the wall is ready for paint.
Drill & Fill Wall Insulation
Signs you need it
You have a pre-1985 Placentia tract home with original stucco and rooms that overheat on summer afternoons. Drill-and-fill works through the exterior or interior surface.
What it costs in Placentia
Drill-and-fill wall insulation in Placentia typically runs $3.50 to $7.00 per square foot depending on blow-in material and surface patching needed.
How we do it
We drill access holes in a regular pattern, fill each cavity with cellulose or fiberglass to the correct density, then patch and smooth each opening to blend with the surrounding surface.
Exterior Wall Insulation
Signs you need it
You’re re-siding or adding stucco, which is the rare moment when exterior wall insulation can be installed without drilling through an existing surface.
What it costs in Placentia
Exterior wall insulation in Placentia is usually folded into a siding or stucco project, typically adding $5.00 to $10.00 per square foot to the overall scope.
How we do it
We remove the old exterior cladding, install the insulation board or batts into the exposed framing, and then your siding or stucco contractor rebuilds over the new thermal layer.
What Wall Insulation Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Injection foam wall insulation | $4.00 – $8.00 per sq ft |
| Drill & fill wall insulation | $3.50 – $7.00 per sq ft |
| Exterior wall insulation | $5.00 – $10.00 per sq ft |
| Interior wall soundproofing | $3.50 – $7.00 per sq ft |
Is it worth insulating the walls of a Placentia home that already has attic insulation?
Usually yes, because walls are a huge share of your home’s surface area. Placentia’s empty stud bays leak heat in both directions, and fill them up means your attic insulation no longer has to compensate for a thermal hole below it.
Can you insulate walls from the inside of my Placentia home?
Yes. We can work from the interior by drilling through drywall and patching afterward. Many homeowners choose exterior access to avoid repainting rooms, but both approaches work and we’ll match the method to your home’s finish.
Attic Cleaning & Rodent Proofing in Placentia
Attic cleaning and rodent proofing in Placentia deals with a problem that’s more concentrated here than in the flatland cities to the west: rats and ground squirrels migrating from the Puente Hills open space tunnel through attic insulation and foul everything they touch. Homes in the older neighborhoods backing up to the preserves routinely need full attic remediation rather than a simple insulation top-off. Attic Cleaning & Rodent Proofing removes the contamination, seals the entry points, and rebuilds the insulation so the problem doesn’t return.
Attic Cleanout
Signs you need it
You hear scratching overhead at night, see droppings near the hatch, or find shredded insulation and nesting material in the attic. These are common in Placentia neighborhoods bordering open space.
What it costs in Placentia
A full attic cleanout in Placentia typically ranges from $2.50 to $5.00 per square foot, depending on how heavily contaminated the insulation is.
How we do it
We vacuum out all contaminated insulation, bag and remove the waste, then inspect the deck and framing for damage or burrows that need attention before anything new goes in.
Attic Sanitizing & Decontamination
Signs you need it
After rodents have been active, urine and feces remain in the wood and dust. Sanitizing is an essential step before new insulation can be safely installed.
What it costs in Placentia
Attic sanitizing and decontamination in Placentia typically runs $1.00 to $2.50 per square foot on top of the cleanout cost.
How we do it
We fog or spray the attic with an EPA-registered antimicrobial treatment that neutralizes odor and bacteria, then let the space dry completely before insulation is replaced.
Rodent Proofing & Exclusion
Signs you need it
You’ve cleaned the attic once and the animals came back. Exclusion is the step that stops re-entry, and it’s the most important part of the whole process for Placentia homes near the Puente Hills corridor.
What it costs in Placentia
Rodent proofing and exclusion in Placentia is usually priced by the linear foot of entry point sealed, typically $15 to $35 per linear foot.
How we do it
We find every gap, vent, and chewed opening, then close them with steel mesh, foam, and physical barriers designed to withstand persistent gnawing from rats and squirrels.
What Attic Cleaning & Rodent Proofing Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Attic cleanout | $2.50 – $5.00 per sq ft |
| Attic sanitizing & decontamination | $1.00 – $2.50 per sq ft |
| Rodent proofing & exclusion | $15 – $35 per linear ft |
| Attic restoration | $1.50 – $3.50 per sq ft |
How fast can you clean and re-insulate a rodent-damaged attic in Placentia?
Most full remediation jobs including cleanout, sanitizing, exclusion, and new blown-in insulation complete in two to three days. The exclusion work takes the most time because every entry point has to be physically closeable before we finish.
Will the rodents come back after you clean my Placentia attic?
Not through the same entry points. Exclusion work means we seal every gap we find, and we re-inspect before the job is signed off. Homes directly against the Puente Hills open space may need periodic monitoring, but a properly sealed attic stays clean.
Home Energy Audit in Placentia
A home energy audit in Placentia is the diagnostic step that tells you which of your home’s problems matter most, before any money goes toward insulation or sealing. Most Placentia tract homes have multiple connected issues empty walls, settled attic batts, leaky top plates, and a diagnostic audit measures each one so the fix list is based on data, not guesswork. Home Energy Audit gives you a priority-ordered answer for what to address first.
Blower Door Test
Signs you need it
Your energy bills are high but you don’t know why, or you want an actual number for how leaky your house is before deciding on air sealing.
What it costs in Placentia
A blower door test in Placentia is usually included in a full home energy audit, but as a standalone test it typically runs $150 to $300.
How we do it
We mount a calibrated fan in an exterior door frame, depressurize the house, and measure exactly how much air leaks through the building envelope, then map the leak zones.
Thermal Imaging Inspection
Signs you need it
Some rooms stay hot while others stay cold, or you suspect missing insulation in walls and ceilings but don’t want to open drywall to find out.
What it costs in Placentia
Thermal imaging in Placentia is typically included in a full audit and costs $250 to $500 as part of a blower-door assisted inspection.
How we do it
We scan every wall, ceiling, and floor with an infrared camera while the blower door runs, which makes cold and heat signatures visible and pinpoints exactly where the envelope is failing.
Insulation Inspection
Signs you need it
The home is pre-1985 and you suspect the attic never got enough insulation, or you’re not sure whether the existing material is still doing its job.
What it costs in Placentia
An insulation inspection in Placentia is often part of the audit and usually adds $100 to $250 to the total when done standalone.
How we do it
We access the attic and walls, measure existing R-values, check for settling or gaps, and document what’s there before we recommend what needs to happen next.
What Home Energy Audit Costs in Placentia
| Item | Typical range in Placentia |
|---|---|
| Blower door test | $150 – $300 |
| Thermal imaging inspection | $250 – $500 |
| Insulation inspection | $100 – $250 |
| Duct leakage test | $150 – $350 |
| Full home energy audit | $400 – $800 |
Does a home energy audit pay for itself in Placentia?
For most Placentia homes, yes, because the audit prevents you from spending on the wrong fix. Empty wall cavities, settled attics, and leaky top plates all need different solutions, and correcting them in the right order saves real money on the repair plan.
How long does a home energy audit take in Placentia?
Most audits run two to four hours depending on home size and how many tests we run. You’ll leave with a clear list of what’s failing and what order to fix it. Call (714) 793-0570 to schedule yours.
Serving Placentia, CA — Our Local Coverage Area
We’re based in the Placentia area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Brands We Service in Placent
Frequently Asked Questions
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Placentia Customers Say
"Straight answer to a straight question: yes it can be fixed, no you don't need a new one, here's what it costs. Took four minutes on the phone. The other place wanted to send someone out for a "consultation"."
— Malik Prince"Attic was at maybe R-11 from the 1970s and blown in over the top would have just buried the problem. They removed the old material, air sealed the top plates and penetrations first, then blew in to R-49. The upstairs is a completely different house in August."
— Steven Kim"Handled the utility rebate paperwork, which knocked a real amount off the final cost."
— Daniel Delaney