Insulation in Lake Forest, CA
Spray foam insulation in Lake Forest typically costs $2.40 to $6.20 per square foot installed, and it’s the material we recommend first for homes in the Saddleback Valley because it’s the only insulation that air-seals while it insulates. Lake Forest sits well beyond the marine layer that cools Irvine and the coastal cities, so attics here routinely top 150°F in July and August, and most of the 1970s through early-1990s El Toro-era tract homes still have their original, settled fiberglass batts that were barely adequate when they were new. Call (714) 793-0570 for an honest assessment of what your attic actually needs, not what a generalist happens to have on the truck.
Why Lake Forest Homes Are Different
Lake Forest was built out as suburban tract housing from the late 1960s through the early 1990s, before California’s Title 24 energy standards had any real teeth. The dominant housing type is single-story and two-story wood-frame construction with original fiberglass batts that have compressed to half or less of their rated R-value after 30 to 50 years of heat, Santa Ana wind cycles, and gravity doing what gravity does. Many of these homes also have attic bypasses around recessed lighting that were never air-sealed, plus garage ceilings beneath living space that got skipped entirely during original construction.
The Saddleback Valley position is the big difference maker. Lake Forest doesn’t get the daily marine-layer buffer that keeps Laguna Niguel and other coastal cities 10 to 15 degrees cooler. When the Santa Anas kick up in September and October, the air dries out, the temperature spikes 15 to 20 degrees in hours, and the HVAC system fights an attic that’s radiating heat straight down through the ceiling. We walk into attics in the Foothill Ranch area and the neighborhoods around El Toro Road and see the same pattern repeatedly: blown-in material settled to half its original depth, batts shifted out of place, and no air sealing whatsoever.
That wide diurnal swing, hot days and cool nights, makes thermal envelope continuity worth more here than in cities with stable coastal air. Every gap costs you twice.
Our Main Lake Forest Services
Most Lake Forest homeowners calling us for the first time are dealing with one of two problems: an attic that’s bleeding heat into the house, or a crawl space that’s pushing moisture up through the floors. These two services handle the bulk of what we see in this valley.
Attic Insulation in Lake Forest
We work on a lot of Lake Forest attics where the original batts have compressed to R-11 or worse, far below the R-38 to R-49 that today’s Title 24 standards call for. The job usually involves removing the old material, air-sealing every penetration, and blowing in fresh coverage to fill the entire attic floor evenly. In homes along Bakerview and off Trabuco Road, the difference after a proper attic job is immediate, rooms stay cooler by early afternoon and the AC cycles far less. Full details are on our Attic Insulation in Lake Forest page.
Crawl Space Encapsulation & Vapor Barrier in Lake Forest
The soil under Lake Forest homes stays damp through the summer irrigation season, and that moisture migrates up into floor assemblies and living spaces. Encapsulation puts a heavy liner across the entire crawl space floor and up the foundation walls, cutting off that moisture path at the source. We do more of this work in the Portola Hills and Baker Ranch neighborhoods than most people realize. Read through the full scope on our Crawl Space Encapsulation & Vapor Barrier in Lake Forest page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Lake Forest
Spray foam insulation in Lake Forest is the highest-performance option for attics that turn into ovens during the summer, and it’s the only single material that stops both conductive heat gain and air leakage in one pass. In the Saddleback Valley’s inland heat, where attic temperatures can exceed 150°F, open-cell foam’s air-sealing capability and closed-cell foam’s R-value per inch make it the material we recommend most often for El Toro-era tract homes with vaulted ceilings, bonus rooms, or HVAC equipment in the attic. Our team installs Spray Foam Insulation using Icynene and Demilec foam systems, and the owner is on-site for every spray day.
Open-Cell Spray Foam
Signs you need it
Rooms over the garage that never cool down, or a second floor that runs 8 to 10 degrees warmer than the main level during a Lake Forest summer.
What it costs in Lake Forest
Open-cell spray foam in Lake Forest attics typically runs $2.40 to $3.60 per square foot of installed foam area.
How we do it
We remove old material where needed, seal conduit and plumbing penetrations, then spray a continuous layer directly onto the attic floor or roofline so nothing can leak air through the assembly.
Closed-Cell Spray Foam
Signs you need it
Humidity problems in an attic HVAC room, or a homeowner who wants the highest R-value per inch in a low-clearance roofline where standard batts won’t fit.
What it costs in Lake Forest
Closed-cell spray foam in Lake Forest typically runs $4.20 to $6.20 per square foot, reflecting both material density and the continuous air barrier it creates.
How we do it
We prep the target area, mask off non-target surfaces, and spray a monolithic closed-cell layer, usually 2 to 3 inches, that both insulates and stops bulk water vapor.
Garage Ceiling Spray Foam
Signs you need it
A bedroom directly above the garage that feels like a hot box every afternoon, which is extremely common in Lake Forest’s two-story tract plans.
What it costs in Lake Forest
Garage ceiling spray foam in Lake Forest generally falls between $2.40 and $4.20 per square foot depending on foam type and access.
How we do it
We spray the interior face of the garage ceiling, typically open-cell, converting that unconditioned buffer into a conditioned or semi-conditioned space.
What Spray Foam Insulation Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Open-cell spray foam (attic floor) | $2.40 – $3.60 per sq ft |
| Closed-cell spray foam (roofline or rim joist) | $4.20 – $6.20 per sq ft |
| Garage ceiling spray foam | $2.40 – $4.20 per sq ft |
| Rim joist spray foam | $3.00 – $5.00 per sq ft |
Is spray foam safe for homes with attic HVAC in Lake Forest?
Yes, when properly installed and allowed to cure, spray foam is safe around HVAC equipment. The key is correct thickness and ventilation design, which we handle based on your home’s specific setup. Call (714) 793-0570 for a straight answer on your attic layout.
Can you spray foam a Lake Forest attic in summer?
Yes. Spray foam can be installed year-round in Lake Forest, and summer is actually the season when most homeowners reach out because the heat problem is undeniable. We’ll schedule you as quickly as weather and material allow.
Blown-In Insulation in Lake Forest
Blown-in insulation in Lake Forest is usually the most practical upgrade for the tract attics that make up most of this city’s housing stock, and it’s what we recommend when the structure’s open attic floor makes it cost-efficient to top up or replace existing coverage. The original batts in homes built between 1968 and 1992 have settled badly, and for most homeowners the right fix isn’t foam, it’s a thorough air-seal followed by dense, even coverage of blown-in material. We install Blown-In Insulation to full Title 24 depths, matched to your attic’s layout and venting.
Blown-In Cellulose
Signs you need it
Attic insulation that’s visibly compressed below the tops of the ceiling joists, or rooms that heat up early in the day during a Lake Forest summer.
What it costs in Lake Forest
Blown-in cellulose in Lake Forest attics typically runs $1.20 to $2.00 per square foot installed.
How we do it
We remove any damaged material, air-seal the attic plane, then blow GreenFiber cellulose to a consistent depth that meets or exceeds current R-value requirements.
Blown-In Fiberglass
Signs you need it
Homes where the existing fiberglass batts are still dry but thin, and the homeowner wants a fast, lower-profile material-add without the weight of cellulose.
What it costs in Lake Forest
Blown-in fiberglass in Lake Forest typically runs $1.00 to $1.80 per square foot installed.
How we do it
We run hoses up through the attic access or through gable openings and blow Knauf fiberglass in an even blanket to the specified depth and R-value.
What Blown-In Insulation Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Blown-in cellulose (full attic) | $1.20 – $2.00 per sq ft |
| Blown-in fiberglass (full attic) | $1.00 – $1.80 per sq ft |
| Dense-pack wall insulation | $1.50 – $2.50 per sq ft |
| Blown-in top-up over existing | $0.90 – $1.50 per sq ft |
How deep should blown-in insulation be in Lake Forest?
For a Lake Forest attic, current code calls for R-38 to R-49 depending on the specific assembly, which works out to roughly 12 to 16 inches of cellulose or 14 to 19 inches of fiberglass. We measure and match to your home, and the estimate is free.
Does blown-in insulation settle in Lake Forest heat?
Cellulose settles slightly in the first year, which is why we install to a calculated over-depth. Fiberglass blown-in resists settling if installed at proper density. Either way, we account for it before the hose ever turns on.
Radiant Barrier Installation in Lake Forest
Radiant barrier installation in Lake Forest attacks a specific problem: solar heat that radiates through the roof deck and down into the attic air, turning the space into a broiler by mid-afternoon. In a city where summer highs hit the mid-90s to low 100s and attic temperatures push past 150°F, a radiant barrier cut that direct radiant gain substantially. We pair Radiant Barrier Installation with insulation in Lake Forest homes where cooling bills stay high even after an attic top-up.
Attic Radiant Barrier
Signs you need it
The attic is nearly unbearable to stand in by noon, and your AC has already run more by 3 p.m. than it should all day.
What it costs in Lake Forest
Radiant barrier stapled under a Lake Forest roof deck typically runs $1.00 to $2.00 per square foot.
How we do it
We staple a reflective foil product to the underside of the rafters, leaving the required air gap above, so radiant heat reflects back toward the roof deck instead of soaking into the insulation below.
Radiant Barrier Roof Deck
Signs you need it
Rooms along the upstairs south or west walls stay hot after sundown, a classic radiant-coupling symptom in Lake Forest’s two-story floor plans.
What it costs in Lake Forest
Radiant barrier roof deck treatment in Lake Forest generally runs $1.00 to $1.80 per square foot of deck area.
How we do it
We work from the attic side, installing the foil across the full roof deck surface below the ridge and above the insulation level, leaving eave and ridge vent passage intact.
What Radiant Barrier Installation Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Radiant barrier (stapled under rafters) | $1.00 – $2.00 per sq ft |
| Radiant barrier roof deck treatment | $1.00 – $1.80 per sq ft |
| Radiant barrier foil (full attic) | $0.80 – $1.50 per sq ft |
| Radiant barrier with ventilation work | $1.50 – $2.50 per sq ft |
Does radiant barrier work without insulation in Lake Forest?
Radiant barrier reduces radiant gain, but it doesn’t replace insulation. In Lake Forest attics you need both because the roof deck heat and the conducted ceiling heat are different problems. We install them together for exactly that reason.
Is radiant barrier worth it on a tile roof in Lake Forest?
Yes. Tile roofs hold heat late into the evening, and a radiant barrier under the deck slows that heat from reaching the insulation and living space below. Most Lake Forest tile-roof homes benefit from it more than homeowners expect.
Insulation Removal & Replacement in Lake Forest
Insulation removal and replacement in Lake Forest is the service most homeowners didn’t know they needed until they look in the attic: 30 to 50 years of rodent activity, dust, moisture, and settled batts don’t get solved by blowing over the top. When the existing material is contaminated, saturated, or compressed beyond usefulness, the only honest answer is to pull it out and start fresh. We handle Insulation Removal & Replacement in Lake Forest attics with the same owner-on-site approach as every other Coastal Insulation job.
Attic Insulation Removal
Signs you need it
Bay insulation that’s black, clumpy, or smells musty, or material that’s been crushed down so far there’s no loft left to insulate anything.
What it costs in Lake Forest
Full attic insulation removal in Lake Forest typically runs $1.20 to $2.50 per square foot, depending on depth and material type.
How we do it
We use a commercial HEPA-filtered vacuum system and run collection hoses from the attic to a sealed container outside, so the old material never passes through your living space.
Contaminated Insulation Removal
Signs you need it
Rodent droppings or nesting scattered through the attic, or visible moisture staining and mold on the batts themselves.
What it costs in Lake Forest
Contaminated insulation removal in Lake Forest typically falls between $1.50 and $3.00 per square foot due to the additional handling and disposal requirements.
How we do it
We treat the affected material as a biohazard removal, bag it on site, and sanitize the exposed surfaces before any new material goes down.
What Insulation Removal & Replacement Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Attic insulation removal (full) | $1.20 – $2.50 per sq ft |
| Contaminated insulation removal | $1.50 – $3.00 per sq ft |
| Vermiculite & old insulation removal | $2.00 – $3.50 per sq ft |
| Insulation replacement (new material) | $1.50 – $3.00 per sq ft |
Can I just blow new insulation over old in Lake Forest?
Sometimes yes, if the old material is dry and clean. But if there’s rodent activity, moisture, or severe settling, topping up just buries the problem. We inspect and tell you straight which route your attic actually needs. Call (714) 793-0570 for an honest assessment.
How long does attic insulation removal take in Lake Forest?
Most single-story Lake Forest attics take one to two days for removal, cleaning, and replacement. Larger two-story homes with limited access run two to three. We’ll give you a firm window before we start.
Attic Air Sealing in Lake Forest
Attic air sealing in Lake Forest is the step that most insulation companies skip, and it’s the reason many homeowners see smaller bill changes than they expected after an insulation-only job. The ceiling plane of a Lake Forest tract home is full of holes: recessed light housings, top plates, plumbing penetrations, and the attic hatch itself, all leaking conditioned air into the attic 24 hours a day. We perform Attic Air Sealing as its own service and as a mandatory prep step before any new insulation goes in.
Attic Floor Air Sealing
Signs you need it
Dirty lines of insulation around the edges of the attic near top plates, or dust pulling through cracks in ceiling fixtures during Santa Ana events.
What it costs in Lake Forest
Attic floor air sealing in Lake Forest typically runs $0.80 to $1.50 per square foot of ceiling area.
How we do it
We sweep aside loose material near each penetration and use can foam or caulk to close every gap, concentrating on the top plates and fixture boxes where most leakage occurs.
Can Light & Duct Boot Sealing
Signs you need it
Recessed lights that feel warm to the touch even when they’re off, and conditioned air disappearing from the duct boots into the attic.
What it costs in Lake Forest
Can light and duct boot sealing in Lake Forest typically runs $15 to $30 per fixture or boot when completed as part of a larger job.
How we do it
We install fire-rated covers over non-IC recessed lights or use IC-safe sealants, and seal every duct boot to the drywall with mastic and foam for an airtight connection.
What Attic Air Sealing Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Attic floor air sealing (full) | $0.80 – $1.50 per sq ft |
| Can light sealing | $15 – $30 per fixture |
| Duct boot sealing | $15 – $30 per boot |
| Attic hatch sealing | $100 – $200 per hatch |
Does air sealing make a big difference in Lake Forest?
Yes. Air leaks carry heat into your attic in winter and pull 150-degree attic air into your home in summer. Sealing cuts that exchange at the source, and for many Lake Forest homes it’s the highest-value dollar-per-degree improvement available.
Can you air seal without replacing my insulation?
Yes, if your existing insulation is still in usable shape. We can seal every penetration and then re-fluff or top up the material you already have. You don’t have to replace what’s working to get the sealing benefit.
Wall Insulation in Lake Forest
Wall insulation in Lake Forest usually means one of two things: filling the empty stud cavities left by 1970s-era construction shortcuts, or adding sound dampening between bedrooms and living space in older two-story floor plans. Many El Toro-era tract homes got minimal or no wall insulation between unconditioned garage and living areas, and daytime heat pours through those uninsulated wall sections long after the attic is addressed. We offer Wall Insulation including drill-and-fill retrofit work that doesn’t require tearing out drywall.
Drill & Fill Wall Insulation
Signs you need it
Exterior walls that feel warm to the touch on a summer evening, or walls that transfer outdoor heat into living space even with the AC running.
What it costs in Lake Forest
Drill-and-fill wall insulation in Lake Forest typically runs $2.00 to $3.50 per square foot of wall area.
How we do it
We drill small access holes in each stud bay and dense-pack cellulose or fiberglass into the cavity at pressure, leaving the wall fully insulated without removing drywall.
Injection Foam Wall Insulation
Signs you need it
Walls where stud bays have obstructions or the homeowner wants a material that will air-seal the cavity, not just fill it.
What it costs in Lake Forest
Injection foam wall insulation in Lake Forest typically runs $3.00 to $5.00 per square foot installed.
How we do it
We inject a low-expansion foam into each cavity through small holes, letting the material expand to fill the bay fully and lock in place permanently.
What Wall Insulation Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Drill & fill wall insulation | $2.00 – $3.50 per sq ft |
| Injection foam wall insulation | $3.00 – $5.00 per sq ft |
| Exterior wall insulation | $2.50 – $4.50 per sq ft |
| Interior wall soundproofing | $2.00 – $3.50 per sq ft |
Can you insulate my existing Lake Forest walls without major demo?
Yes. Drill-and-fill and injection foam methods work from the exterior or interior through small holes, which get patched and painted afterward. We don’t need to remove drywall to fill empty stud bays.
Will wall insulation help with traffic noise in Lake Forest?
Yes, especially on homes near busy roads like El Toro Road or the 241 corridor. Dense-pack cellulose or Rockwool in wall cavities reduces both heat transfer and sound, which is a double win in this valley.
Attic Cleaning & Rodent Proofing in Lake Forest
Attic cleaning and rodent proofing in Lake Forest is about protecting the investment you already made in your home, and it’s one of the most common calls we get from this city’s older tract neighborhoods. The same 30-to-50-year-old homes we insulate have decades of rodent entry points: gaps at eave-roof intersections, utility penetrations, and unsealed vents that let roof rats and mice move in during the mild Lake Forest winters. We provide Attic Cleaning & Rodent Proofing as a complete service, not a quick poison-and-go.
Attic Cleanout
Signs you need it
Scratching noises at night, droppings in the garage near the hatch, or nesting material visible around attic edges when you pop your head up.
What it costs in Lake Forest
A full attic cleanout in Lake Forest typically runs $800 to $1,500 depending on attic size and degree of contamination.
How we do it
We remove all contaminated insulation and debris, HEPA-vacuum the entire attic floor, and bag everything for proper disposal before we think about new material.
Rodent Proofing & Exclusion
Signs you need it
Evidence of repeat entry even after attic cleaning, or daylight visible around vent screens and eave edges when you inspect the roofline.
What it costs in Lake Forest
Rodent proofing and exclusion in Lake Forest typically runs $500 to $1,200 depending on the number of entry points and attic access complexity.
How we do it
We seal every gap, install steel screens over vents, and close off eave and soffit openings with materials rodents can’t chew through, then verify the seal from inside and out.
What Attic Cleaning & Rodent Proofing Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Attic cleanout (full) | $800 – $1,500 |
| Rodent proofing & exclusion | $500 – $1,200 |
| Attic sanitizing & decontamination | $400 – $900 |
| Attic restoration (cleaning + new insulation) | $2,000 – $5,000 |
Do you just kill the rodents, or actually fix the problem in Lake Forest?
We exclude. Anyone can set traps. The permanent fix is sealing every entry point so new rodents can’t get in, then cleaning and restoring the attic so it’s not attractive habitat. Call (714) 793-0570 and we’ll inspect the actual entry points.
How do rodents get into Lake Forest attics?
Roof rats and mice climb stucco and brick easily, then enter through vent screens, eave gaps, and utility line penetrations. Lake Forest’s older tract homes have dozens of such points, and sealing all of them is the only durable solution.
Home Energy Audit in Lake Forest
A home energy audit in Lake Forest is the diagnostic step that tells you exactly where heat is entering your home and where your conditioned air is leaving it, before you spend a dollar on fixes. In a Saddleback Valley home where the attic runs 150°F and the Santa Anas spike the outdoor temperature 20 degrees in a day, guessing at the biggest leak is a losing strategy. We offer Home Energy Audit services using blower door testing and thermal imaging so every recommendation we make is based on measured data from your actual house.
Blower Door Test
Signs you need it
High energy bills without an obvious single cause, or rooms that won’t hold temperature no matter how the thermostat is set.
What it costs in Lake Forest
A blower door test in Lake Forest typically runs $300 to $500 as a standalone service.
How we do it
We mount a calibrated fan in your front door frame, depressurize the house, and measure the total air leakage rate, usually expressed in ACH50.
Thermal Imaging Inspection
Signs you need it
Cold spots in winter or hot spots in summer along walls and ceilings that suggest missing insulation or air leakage in specific stud bays.
What it costs in Lake Forest
Thermal imaging inspection in Lake Forest typically costs $200 to $400, often bundled with the blower door test.
How we do it
We scan the interior walls and ceilings with an infrared camera while the blower door is running, then mark every location where leaks show up so they can be sealed directly.
What Home Energy Audit Costs in Lake Forest
| Item | Typical range in Lake Forest |
| Blower door test | $300 – $500 |
| Thermal imaging inspection | $200 – $400 |
| Insulation inspection | $150 – $300 |
| Duct leakage test | $200 – $400 |
Do I need an energy audit before insulation work in Lake Forest?
Not always, but it often changes what we’d recommend. For older Lake Forest tract homes with multiple possible leak sources, an audit prevents paying for insulation that won’t fix the actual problem the homeowner sees.
How long does a home energy audit take in Lake Forest?
Most Lake Forest audits take 2 to 3 hours depending on house size and how many attic and crawl space access points we need to inspect. You get the report and recommendations same day.
Brands We Service in Lake Forest
We work with Knauf fiberglass, Rockwool mineral wool, CertainTeed insulation products, and Icynene spray foam, among others. Material is ordered per job from local distributors, so nothing sits in a warehouse. Turnaround on product orders for Lake Forest jobs is typically one to three business days. See our brands for the full list.
Pricing for Insulation in Lake Forest, CA
| Service | Typical range in Lake Forest |
| Open-cell spray foam | $2.40 – $3.60 per sq ft |
| Closed-cell spray foam | $4.20 – $6.20 per sq ft |
| Blown-in cellulose | $1.20 – $2.00 per sq ft |
| Blown-in fiberglass | $1.00 – $1.80 per sq ft |
| Radiant barrier | $1.00 – $2.00 per sq ft |
| Attic insulation removal | $1.20 – $2.50 per sq ft |
| Attic air sealing | $0.80 – $1.50 per sq ft |
| Drill & fill wall insulation | $2.00 – $3.50 per sq ft |
| Attic cleanout | $800 – $1,500 |
| Home energy audit | $300 – $500 |
What pushes price up in Lake Forest is attic access: tighter two-story roofs and attached-garage layouts in older tracts require more setup and hose work. The price we quote is the price you pay, no surprise line items added after the job starts.
Neighborhoods We Serve in Lake Forest
We work throughout Lake Forest, including the older El Toro-era tracts and the newer master-planned communities on the city’s perimeter. Response time is usually same-day or next-day for emergency attic issues and within one to two weeks for scheduled installations.
- Foothill Ranch
- Portola Hills
- Baker Ranch
- Woods at Lake Forest
- El Toro Village
Service Area — Cities Near Lake Forest
Coastal Insulation Santa Ana serves Lake Forest and the surrounding south Orange County communities. Our coverage includes Laguna Woods, CA to the south, Tustin, CA to the northwest, Newport Beach, CA on the coast, and our home base in Santa Ana, CA. We’ve served Lake Forest since 2012.
Serving Lake Forest, CA — Our Local Coverage Area
We’re based in the Lake Forest area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Insulation in Lake Forest
We can usually reach Lake Forest same-day for urgent issues like exposed live wiring in a cleaned attic or a failed insulation retrofit that’s left your home exposed. Standard inspections and installations are scheduled within one to two weeks. Call (714) 793-0570 and we’ll tell you our actual current availability.
Interior attic and wall insulation work generally doesn’t trigger HOA review in Lake Forest, since it doesn’t change the exterior appearance. Exterior wall insulation or vent changes along the roofline might, and we help you flag anything that needs board approval before we start.
We work heavily in Foothill Ranch, Portola Hills, Baker Ranch, and the original El Toro-era tracts around Lake Forest and El Toro Road. The older neighborhoods consistently need removal and sealing work, while the newer communities more often call us for radiant barrier and garage ceiling upgrades.
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Lake Forest Customers Say
"Work is good and the house is noticeably more comfortable. There was insulation debris left in the hall closet under the attic access that I had to clean up."
— Kristen Miller"Solid job. It's hard to verify what's up there once they've gone, so I'd suggest asking for photos, which they did provide when I asked but didn't offer."
— Neil Bennett"Found and sealed a gap around the chimney chase that was basically an open chimney to the attic."
— Rafael Vargas